ENCORE™/ZIF G4 Processor Upgrade Card for G3/G4 Power Macintosh® ComputersQuick Start Guide For Encore/ZIF G4Power Macintosh and Operating System Com
8Figure 24 2. Locate the clip securing the processor heat sink to the ZIF socket (Figure 24). Carefully insert a small flat blade screwdriver between
9Hardware Installation—G3 Minitower/Server G3 3. Grasp the Encore/ZIF card so that the narrow end of the card is pointing toward you (Figure 28). Hol
10Figure 32Figure 33Figure 34Hardware Installation—G3 Minitower/Server G3Close Computer 1. Arrange the wires and cables inside the computer so that n
11Hardware Installation—G3 Minitower/Server G3 5. Tip your computer back into the upright position, and then replace the side access panel (Figure 36
12Hardware Installation—G3 All-in-oneFigure 40Figure 39Figure 38Figure 37This section covers the installation of the Encore/ZIF G4 processor upgrade c
13Hardware Installation—G3 All-in-oneFigure 44Figure 43Figure 42Figure 41 3. Remove the screw securing the cable support bracket to the rear panel (F
14Hardware Installation—G3 All-in-oneFigure 48Figure 47Figure 46Figure 45 1. Disconnect the internal drives power cable connectors (Figure 45). 2.
15Hardware Installation—G3 All-in-oneFigure 52Figure 51Figure 50Figure 49 5. While squeezing its release tab, disconnect the logic board power connec
16Hardware Installation—G3 All-in-oneFigure 55Figure 54Figure 53Install Encore/ZIF Processor Upgrade Card 1. Remove the Encore/ZIF card from its anti
17Hardware Installation—G3 All-in-oneFigure 59Figure 58Figure 57Reconnect Logic Board Cables and Install Power Adapter CableExcept for the power cable
This page left intentionally blank.
18Hardware Installation—G3 All-in-oneFigure 63Figure 62Figure 61Replace Cable Support Bracket 1. Insert the cable support bracket underneath the logi
19Figure 65Figure 66Figure 67Figure 68Hardware Installation—G3 Blue & White, G4 PCI GraphicsThis section covers the installation of the Encore/ZIF
20Figure 69Figure 72Hardware Installation—G3 Blue & White, G4 PCI Graphics 2. Locate the clip securing the processor heat sink to the ZIF socket
21Figure 75Figure 76Hardware Installation—G3 Blue & White, G4 PCI GraphicsEncore/ZIF cardpower adapter cable8-pin connectorRemove System Bus Jumpe
22Figure 79Figure 80Hardware Installation—G3 Blue & White, G4 PCI Graphics 4. While applying moderate pressure on top of the Encore/ZIF card’s he
23Hardware Installation—G3 Blue & White, G4 PCI GraphicsFigure 81Figure 82adapter cable side panelClose Computer 1. Arrange the wires and cables
24This section covers the installation of additional software your system may require to fully support the Encore/ZIF G4 processor upgrade card. Compl
25Installing Additional SoftwareEnable AltiVec—Existing OS 9.0.x installation (continued) 3. Double-click the Mac OS Install icon. Proceed through th
26Installing Additional SoftwareUpdating and Maintaining Mac OS X—All Systems Except Power Mac G4 (PCI Graphics)At some time in the future, you may wi
1Install or Upgrade to Mac OS 9.2.x or Later, If Necessary—Power Macintosh G3 Blue & White and Power Mac G4 (PCI Graphics) UsersIf you have either
2Hardware Installation—G3 DesktopThis section covers the installation of the Encore/ZIF G4 processor upgrade card into Power Macintosh G3 Desktop comp
3 8. Locate the spring clip on the internal assembly (Figure 5), unhook and remove it from the assembly; do not reinstall the spring clip. Remove Hea
4Install Encore/ZIF Processor Upgrade Card 1. Remove the Encore/ZIF card from its anti-static package, mak-ing sure to handle the card by its edges (
5Install Power Adapter Cable Between Computer and Encore/ZIF Card 1. Locate the logic board power cable plugged in next to the Encore/ZIF card (Figur
6 3. Rotate and carefully lower the internal assembly back into the computer’s case (Figure 17), making sure that no wires or cables get pinched or c
7This section covers the installation of the Encore/ZIF G4 processor upgrade card into Power Macintosh G3 Minitower and Macintosh Server G3 systems. I
Comentários a estes Manuais